| Channels |
| |
16 grouped into 8 stereo pairs |
| Input Impedance |
| |
28K ohms |
| Bandwidth -3dB |
| |
3Hz to 50KHz |
| Frequency Response @ 1W 8ohm |
| |
Flat +0, -0.1dB from 20Hz to
20KHz |
| Total Harmonic Distortion (THD)
@ full power |
| |
0.03% or less |
| IHF I.M. Distortion |
| |
0.01% or less |
| SMPTE I.M. Distortion |
| |
0.03% or less |
| Dynamic Headroom |
| |
2dB or more |
| Signal/Noise Ratio (S/N) "A"
Weighted |
| |
>110dB |
| Gain |
| |
28dB |
| Damping Factor |
| |
>1000 |
| Channel Separation over full
bandwidth |
| |
>100dB |
| Environmental Temperature Range |
| |
41-104°F (5-40°C) |
| Environmental Humidity |
| |
10% to 90% RH (non-condensing) |
| Power Requirements |
| |
120VAC, 50-60 Hz, 1800W and
24VDC, .5A, 12W network |
| Power |
| |
Input Requirements |
120VAC +/-10%, 50-60Hz, 1800
Watts |
| |
Cresnet Power Requirements |
24VDC @ .5A, 12 Watts |
| Output Power |
| |
8 ohm load |
60 Watts/Channel; All channels
driven, 20Hz to 20KHz, at rated THD |
| |
4 ohm load |
90 Watts/Channel |
| |
8 ohm load Bridged |
220 Watts/Channel (CNXBRMD required) |
| Rear Indicators |
| |
PWR |
Green LED is illuminated when
24 VDC Via the Cresnet connection is supplied to the CNAMPX-16X60. |
| |
NET |
Yellow LED indicates that the
SIMPL program currently loaded in the control system has a network
device defined at the same NET ID code as the CNAMPX-16X60.
LED flashes when communication with the Cresnet system and the
CNAMPX-16X60 is occurring |
| |
OVERRIDE Button & Indicator |
OVERRIDE button is used to activate
AC power and activate all room outputs. Button functions only
when 24VDC is applied to the NET connector. Red LED illuminates
when the OVERRIDE is activated |
| Rear Ports |
| |
NET |
The 4-pin network connector
is used to connect the CNAMPX-16X60 to the Cresnet system |
| |
Power Connector and Fuse Compartment |
The power connector provides
AC operating power to the CNAMPX-16X60 via the supplied power
cord. The fuse electrically protects the internal circuitry
from power overloads and is located (a spare fuse is included)
within the compartment above the power connector |
| |
AUDIO INPUTS 1 - 8 |
Each of the eight pair of RCA
connectors is typically used to connect the pre-amplified audio
from the CNX-PAD8A or CNXBIPAD8 to the CNAMPX-16X60.The left
channel audio is input to the connectors with the white center
insulators and right channel audio connectors have red center
insulators |
| |
SPEAKER OUTPUTS 1 - 8 |
These eight pair of speaker
dual-binding posts output the left and right amplified audio
to the corresponding speakers.The audio positive posts have
RED screw-on caps and the audio negative posts have BLACK screw-on
caps. Each post is gold-plated and accepts bare wire, banana
plugs, or spade lugs |
| Dimensions |
| |
7.69" / 19.53 cm (H)x
19.00" / 48.26 cm (W)x
17.22" / 43.74 cm (D) |
| Weight |
| |
81.40lb (37.00Kg) |
| Rack Space Required |
| |
4 rack units (minimum of 1 additional
rack space should be provided above and below amp for proper
ventilation); Rack mounting ears are included |
| Model Options |
| The CNAMPXI-16X60 (International
Version) has all the features of the CNAMPX-16x60, with the
following exceptions: |
| |
Input Power Requirements |
230VAC, +/-10%, 50-60 Hz, 1800W |
| |
Room output ports do not accept
banana plugs |
